RAM Ram Dodge 2010 Owner'S Manual Download Page 137

Page: 137 / 616

WARNING DISPLAY DISTANCES

DISPLAY MESSAGE

OBSTACLE DISTANCE FROM:

ARC’s

AUDIBLE

SIGNAL

REAR CORNERS

REAR CENTER

Park Assist ON

None

Warning Object Detected

78.7 in (200 cm)

3 Solid

Yes, 1/2 second

Warning Object Detected

39.3 in (100 cm)

3 Flashing

Slow Tone

Warning Object Detected

27.5 in (70 cm)

31.4 in (80 cm)

3 Flashing

Slow Tone

Warning Object Detected

25.5 in (65 cm)

2 Flashing

Fast Tone

Warning Object Detected

19.7 in (50 cm)

2 Flashing

Fast Tone

Warning Object Detected

15.7 in (40 cm)

2 Flashing

Fast Tone

Warning Object Detected

11.8 in (30 cm)

1 Flashing

Continuous Tone

NOTE: ParkSense

威

will MUTE the radio, if on, when the system is sounding an audio tone.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

135

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Ram Dodge 2010

Reviews:

Related manuals for Ram Dodge 2010

Brands by name

Popular brands

RAM Ram Dodge 2010, Owner'S Manual

Search results

Summary of Contents for Ram Dodge 2010

Reviews:

Related manuals for Ram Dodge 2010

Brands by name

Popular brands