manualshive.com logo in svg

RAM Ram Dodge 2010, Owner'S Manual, Page: 256 / 616

Share
Download
RAM Ram Dodge 2010 Owner'S Manual Download Page 256

MEDIA CENTER 130 (RES/RSC) — AM/FM
STEREO RADIO WITH CD PLAYER (MP3 AUX
JACK) AND SIRIUS RADIO

NOTE:

The radio sales code is located on the lower right

side of the radio faceplate.

Operating Instructions — Radio Mode

NOTE:

The ignition switch must be in the ON/RUN or

ACC position to operate the radio.

Power Switch/Volume Control (Rotary)

Push the ON/VOLUME control knob to turn on the
radio. Push the ON/VOLUME control knob a second
time to turn off the radio.

Electronic Volume Control

The electronic volume control turns continuously (360
degrees) in either direction without stopping. Turning the
ON/VOLUME control knob to the right increases the
volume and to the left decreases it.

When the audio system is turned on, the sound will be
set at the same volume level as last played.

SEEK Buttons

Press and release the SEEK buttons to search for the next
listenable station in AM/FM mode. Press the right switch

Media Center 130 (RES/RSC)

254

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews:

No comments