manualshive.com logo in svg

RAM Ram Dodge 2010, Owner'S Manual


Share
Download
background image

NOTE:

Under no circumstances should oil change

intervals exceed 6,000 miles (10 000 km) or six months,
whichever occurs first.

Engine Oil Selection

For best performance and maximum protection under all
types of operating conditions, the manufacturer only
recommends engine oils that are API Certified and meet
the requirements of Chrysler Material Standard MS-6395.

American Petroleum Institute (API) Engine Oil
Identification Symbol

This symbol means that the oil has
been certified by the American
Petroleum Institute (API). The
manufacturer only recommends
API Certified engine oils.

CAUTION!

Do not use chemical flushes in your engine oil as the
chemicals can damage your engine. Such damage is
not covered by the New Vehicle Limited Warranty.

Engine Oil Viscosity (SAE Grade)

SAE 5W-20 engine oil is recommended for all operating
temperatures. This engine oil improves low temperature
starting and vehicle fuel economy. The engine oil filler
cap also shows the recommended engine oil viscosity for
your engine. For information on engine oil filler cap
location, refer to “Engine Compartment” in “Maintaining
Your Vehicle” for further information.

NOTE:

Vehicles equipped with a 5.7L engine must use

SAE 5W-20 oil. Failure to do so may result in improper
operation of the Multi-Displacement System (MDS). Re-
fer to “Multi-Displacement System” in “Starting and
Operating” for further information.

516

MAINTAINING YOUR VEHICLE

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Ram Dodge 2010

AA Products X31 Instruction Manual preview
X31
Brand: AA Products Pages: 6
Camcar 40000 Manual preview
40000
Brand: Camcar Pages: 6
Vauxhall Cascada Quick Reference Manual preview
Cascada
Brand: Vauxhall Pages: 2
Federal Signal Corporation CommCenter D1 Series Installation And Service Instructions Manual preview
CommCenter D1 Series
Brand: Federal Signal Corporation Pages: 16
BMW 3-series convertible Complete Vehicle Workbook preview
3-series convertible
Brand: BMW Pages: 98
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Brand: iRacing Pages: 25
Harbor Freight Tools 66242 User Manual preview
66242
Brand: Harbor Freight Tools Pages: 12
Honda 0SR95-HL4-211A Installation Instructions preview
0SR95-HL4-211A
Brand: Honda Pages: 3
Metra Electronics 99-7860 Installation Instructions preview
99-7860
Brand: Metra Electronics Pages: 5
Renkforce RF-4743771 Operating Instructions preview
RF-4743771
Brand: Renkforce Pages: 4
Mazda 0000-8L-G03A Installation Instructions preview
0000-8L-G03A
Brand: Mazda Pages: 3
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Brand: RAM Pages: 360
Phonocell 6/821 Mounting Instructions preview
6/821
Brand: Phonocell Pages: 8
Brainz 38508 Instruction Manual preview
38508
Brand: Brainz Pages: 2
Reese 50085 Installation Instructions Manual preview
50085
Brand: Reese Pages: 21
Curtis 1POLXP1000GS Installation & Owner'S Manual preview
1POLXP1000GS
Brand: Curtis Pages: 5
XTC RZR-SW-USB-2B Manual preview
RZR-SW-USB-2B
Brand: XTC Pages: 2
Champion Power Equipment 14560 Owner'S Manual & Operating Instructions preview
14560
Brand: Champion Power Equipment Pages: 21

Brands by name

Popular brands

Load more brands