RAM Ram Dodge 2010 Owner'S Manual Download Page 83 | Manualshive

Page: 83 / 616

RAM Ram Dodge 2010 Owner'S Manual Download Page 83

The engine oil installed in the engine at the factory is a
high-quality energy conserving type lubricant. Oil
changes should be consistent with anticipated climate
conditions under which vehicle operations will occur. For
the recommended viscosity and quality grades refer to
“Maintenance Procedures” in “Maintaining Your Ve-
hicle”. NON-DETERGENT OR STRAIGHT MINERAL
OILS MUST NEVER BE USED.

A new engine may consume some oil during its first few
thousand miles (kilometers) of operation. This should be
considered a normal part of the break-in and not inter-
preted as an indication of difficulty.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

81

«
...
81
82
83
84
85
...
»

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews:

No comments