Home
/
RAM
/
Ram Dodge 2010
/
Owner'S Manual

RAM Ram Dodge 2010, Owner'S Manual, Page: 178 / 616

Share

Page: 178 / 616

RAM Ram Dodge 2010 Owner'S Manual Download Page 178

To open a storage bin, press and release the button
located on the lid. The RamBox

威

lid will open upward to

allow hand access. Lift the lid to fully open.

The interior of the RamBox

威

will automatically illumi-

nate when the lid is opened. In addition to the automatic
illumination switch, there is a manual on/off switch
located at the rear of each storage bin. Pushing the switch
once will turn off the bin lights, pushing the switch again
will turn the lights back on.

RamBox

威

Pushbutton and Lock

RamBox

威

Light Switch

176

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
176
177
178
179
180
...
»

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews:

No comments