manualshive.com logo in svg

RAM Ram Dodge 2010, Owner'S Manual, Page: 175 / 616

Share
Download
RAM Ram Dodge 2010 Owner'S Manual Download Page 175

2. Grasp the knob on the load floor and lift the knob until
the load floor unfolds into position.

3. Reverse the procedure to store the load floor.

Positioning the Load Floor for Storage Access Under
the Seat

1. Lift the 60/40 seat cushion(s) to the upward position.

2. Unsnap the securing snap located at either side of the
load floor.

3. Lift the load floor up to access storage under the load
floor.

Load Floor In Open Position

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

173

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews:

No comments