manualshive.com logo in svg

RAM Ram Dodge 2010, Owner'S Manual, Page: 171 / 616

Share
Download
RAM Ram Dodge 2010 Owner'S Manual Download Page 171

Storage and Seats (Crew Cab)

The Crew Cab models provide additional storage under
the rear seats. Lift the seats to access the storage com-
partment.

To open the storage compartments, lift upward on the
handle of the latch and open the lid.

CAUTION!

Always lift the storage compartment lids by using
the handle. Failure to lift the lids by using the handle
can result in damage to the lids.

Crew Cab Storage

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

169

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews:

No comments