RAM Ram Dodge 2010 Owner'S Manual Download Page 45 | Manualshive

Page: 45 / 616

background image

5. Position the shoulder belt on your chest so that it is
comfortable and not resting on your neck. The retractor
will withdraw any slack in the belt.

6. To release the belt, push the red button on the buckle.
The belt will automatically retract to its stowed position.
If necessary, slide the latch plate down the webbing to
allow the belt to retract fully.

WARNING!

A frayed or torn belt could rip apart in an accident
and leave you with no protection. Inspect the belt
system periodically, checking for cuts, frays, or loose
parts. Damaged parts must be replaced immediately.
Do not disassemble or modify the system. Seat belt
assemblies must be replaced after an accident if they
have been damaged (bent retractor, torn webbing,
etc.) or if the airbag deployed.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

43

«
...
43
44
45
46
47
...
»

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Ram Dodge 2010

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: Front Runner Pages: 5

Brand: GATmatic Pages: 13

Brand: Wagan Pages: 8

Brand: Thermo King Pages: 2

Brand: Hama Pages: 40

Brand: WABCO Pages: 52

Brand: Park-Daddy Pages: 22

Brand: Chevrolet Pages: 428

Brand: v.link Pages: 19

Brand: Thule Pages: 8

Brand: true-i Pages: 11

Brand: Edelbrock Pages: 2

Brand: Mercedes-Benz Pages: 93

Brand: Edelbrock Pages: 1

Brand: Summit Racing Pages: 11

Brand: EUFAB Pages: 18

SHERPA SADDLE BAG JL

Brand: Overland Outfitters Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands