Home
/
RAM
/
Ram Dodge 2010
/
Owner'S Manual

RAM Ram Dodge 2010, Owner'S Manual, Page: 481 / 616

Share

Page: 481 / 616

RAM Ram Dodge 2010 Owner'S Manual Download Page 481

WARNING!

After using the jack and tools, always reinstall them
in the original carrier and location. While driving
you may experience abrupt stopping, rapid accelera-
tion or sharp turns. A loose jack, tools, bracket or
other objects in the vehicle may move around with
force, resulting in serious injury.

Reinstalling The Jack And Tools (1500 Series)

1. Lower the jack all the way down by turning the jack
turn-screw until the jack is snug.

2. Position the jack and tool bag (unrolled). Make sure
the lug wrench is under the jack near the jack turn-screw.

Turn Screw and Lug

6

WHAT TO DO IN EMERGENCIES

479

«
...
479
480
481
482
483
...
»

Summary of Contents for Ram Dodge 2010









































































































































































































































































































































































































































































































































































































































Reviews:

No comments