manualshive.com logo in svg

Radware Alteon, Application Manual

Share
Download
Radware Alteon Application Manual Download Page 837

 

Alteon Application Switch Operating System Application Guide

IPv6

Document ID: RDWR-ALOS-V2900_AG1302

 

837

IPv6 Address Types

There are three types of IPv6 addresses:

•

Unicast, page 837

•

Multicast, page 837

•

Anycast, page 837

Unicast

There are two types of unicast addresses:

•

Global unicast address—This is an address that can be reached and identified globally. Global 
unicast addresses use the high-order bit range from 2000 to 3FFF. If the last 64 bits of the 
address are not configured, Alteon defaults to the EUI-64 (Extended Unique Identifier 64-bit) 
address format. RFC 3513 defines the expanding of the Ethernet MAC address based on a 48-bit 
format into a 64-bit EUI-64 format.
The interface ID must be unique within the same subnet.

•

Link-local unicast address—This is an address used to communicate with a neighbor on the 
same link. Link-local addresses use the high-order bit range from FE80 to FEBF. Link-local 
unicast addresses are configured on the interface by using the link-local prefix FE80::/10 and 
the interface identifier in EUI-64 format for its low-order 64-bit. Link-local packets are not 
routed between subnets.

Multicast

A multicast address (FF00 to FFFF) is an identifier for a group interface. The multicast address most 
often encountered is a solicited-mode multicast address using prefix FF02::1:FF00:0000/104 with 
the low-order 24 bits of the unicast or anycast address.

Anycast

Anycast addresses can be global unicast, site-local or link-local addresses used for a one-to-nearest 
node member of the anycast group communication. Alteon does not support anycast addresses.

Pinging IPv6 Addresses

The following are examples of pinging IPv6 addresses:

To ping an IPv6 address

>> Main# /info/l3/nbrcache

>> IP6 Neighbor Discovery Protocol# ping6 3000::1

3000:0:0:0:0:0:0:1 is alive

Summary of Contents for Alteon











































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands