Quectel UG Series Command Manual Download Page 54

Page: 54 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 53 / 247

Parameter

UG95 module does not support this function.

4.3.13. AT+QCFG="sms/textescape" Character Escape of SMS Text

This command is similar to AT+QCFG="ussd/textescape". The only difference is this command affects

SMS text.

<enable>

0 Character escape function of USSD text is disabled

1 Character escape function of USSD text is enabled

When AT+CSCS=

“GSM” or AT+CSCS=“IRA”, in USSD text outputting:

0x5C (show in hex, character

in GSM, character \ in ASCII) will be

escaped into 0x5C3543

(“\5C”).

0x0D (show in hex, character <CR> in GSM and IRA) will be escaped into

0x5C3044

(“\0D”).

0x0A (show in hex, character <LF> in GSM and IRA) will be escaped into

0x5C3041

(“\0A”).

0x22 (show in hex, c

haracter “ in GSM and IRA) will be escaped into

0x5C3232 (“\22”).

0x00 (show in hex, character @ in GSM) will be escaped into 0x5C3030

(“\00”).

AT+QCFG="sms/textescape" Character Escape of SMS Text

Write Command

AT+QCFG="sms/textescape"[,<enabl

e>]

Response

If configuration parameters are omitted

(

+QCFG="sms/textescape"

), return current configuration:

+QCFG: "sms/textescape",<enable>

If configuration parameters are entered:

ERROR

If error is related to ME functionality:

+CME ERROR: <err>

Reference

NOTE

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands