Quectel UG Series Command Manual Download Page 56

Page: 56 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 55 / 247

Parameter

This default

value is “0” for no “remoteip” negotiation function. New settings are saved in NV. This function

becomes effective immediately.

Example

AT+QCFG="remoteip"

Check current status

+QCFG: "remoteip",0

AT+QCFG="remoteip",1

//Setting the

“remoteip” negotiation active

AT+QCFG="remoteip"

Check current status

+QCFG: "remoteip",1

AT+QCFG="remoteip",0

//Settin

g the “remoteip” negotiation inactive

AT+QCFG="remoteip"

Check current status

+QCFG: "remoteip",0

4.3.15. AT+QCFG= "ppp/firstreqintr" Extension Configuration

AT+QCFG=

“ppp/firstreqintr” is used to set the interval between CONNECT and first CONFIG_REQ frame

of PPP.

<remoteIPsel>

Disable/enable the

function of “remoteip” negotiation

efault value, no “remoteip” negotiation

ctive “remoteip” negotiation

AT+QCFG Extension Configuration

Test Command

AT+QCFG=?

Response

……

+QCFG: "ppp/firstreqintr"

,(1000

10000)

……

NOTE

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands