Quectel UG Series Command Manual Download Page 173

Page: 173 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 172 / 247

Parameter

<status>

=0 should be returned only if service is not active for any

<class>

i.e. +CCWA: 0, 7 will be

returned in this case.

2. When

<mode>

=2, all active call waiting classes will be reported. In this mode the command is

aborted by pressing any key.

3. Unsolicited result code:

When the presentation call waiting at the TA is enabled (and call waiting is enabled) and a terminating

call set up during an established call, an unsolicited result code is returned:

+CCWA: <number>,<type>,<class>,[<alpha>],<CLI_validity>

Example

AT+CCWA=1,1

//Enable presentation of an unsolicited result code

ATD10086;

//Establish a call

<n>

Disable presentation of an unsolicited result code

Enable presentation of an unsolicited result code

<mode>

When

<mode>

parameter is not given, network is not interrogated

Disable

Enable

Query status

<class>

A sum of integers, each integer represents a class of information

Voice (telephony)

Data (bearer service)

FAX (facsimile)

Data circuit sync

Data circuit async

<status>

Disable

Enable

<number>

Phone number in string type of calling address in format specified by

<type>

Type of address octet in integer format

129 Unknown type (IDSN format number)

145 International number type (ISDN format )

<alpha>

Optional string type alphanumeric representation of

<number>

corresponding to the

entry found in phone book

<CLI_validity>

Integer type

0 CLI valid

1 CLI has been withheld by the originator

2 CLI is not available due to interworking problems or limitations of originating network

NOTES

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands