Quectel UG Series Command Manual Download Page 33

Page: 33 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 32 / 247

Parameter

3.3. AT+IFC Set TE-TA Local Data Flow Control

AT+IFC determines the flow control behavior of the serial port.

Parameter

Maximum Response Time

300ms

Reference

V.25ter

<value>

TA ignores status on DTR



OFF on DTR: Change to command mode while remaining the connected call



OFF on DTR: Disconnect data call, and change to command mode. During

state DTR=OFF, auto-answer function is disabled

AT+IFC Set TE-TA Local Data Flow Control

Test Command

AT+IFC=?

Response

+IFC:

(list of supported

<dce_by_dte>

s),(list of supported

<dte_by_dce>

Read Command

AT+IFC?

Response

+IFC: <dce_by_dte>,<dte_by_dce>

Write Command

AT+IFC=<dce_by_dte>,<dte_by_dce>

Response

This parameter setting determines the data flow control on

the serial interface for data mode.

Maximum Response Time

300ms

Reference

V.25ter

<dce_by_dte>

Specifies the method that will be used by TE when receiving data from TA

None

RTS flow control

<dte_by_dce>

Specifies the method that will be used by TA when receiving data from TE

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands