Quectel UG Series Command Manual Download Page 28

Page: 28 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 27 / 247

Parameter

2.23. AT+CFUN

Set Phone Functionality

AT+CFUN controls the functionality level. It can also be used to reset the UE.

Parameter

<value>

CONNECT

result code only returned; dial tone and busy detection are both disabled

CONNECT<text>

result code only returned; dial tone and busy detection are both

disabled

CONNECT<text>

result code returned; dial tone detection is enabled; busy detection is

disabled

CONNECT<text>

result code returned; dial tone detection is disabled; busy detection

is enabled

CONNECT<text>

result code returned; dial tone and busy detection are both enabled

AT+CFUN Set Phone Functionality

Test Command

AT+CFUN=?

Response

+CFUN:

(list of supported

<fun>

s),(list of supported

<rst>

Read Command

AT+CFUN?

Response

+CFUN: <fun>

Write Command

AT+CFUN=<fun>[,<rst>]

Response

If error is related to ME functionality:

+CME ERROR: <err>

Maximum Response Time

15s, determined by network.

Reference

3GPP TS 27.007

<fun>

Minimum functionality

Full functionality (Default)

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands