Quectel UG Series Command Manual Download Page 179

Page: 179 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 178 / 247

Parameter

Read Command

AT+COLP?

Response

+COLP: <n>,<m>

Write Command

AT+COLP=<n>

Response

TA enables or disables the presentation of the COL

(Connected Line) at the TE for a mobile originating a call. It

has no effect on the execution of the supplementary service

COLR in the network.

Intermediate result code is returned from TA to TE before any

+CR or V.25ter responses.

Maximum Response Time

15s, determined by network.

Reference

3GPP TS 27.007

<n>

Parameter sets/shows the result code presentation status in the TA

Disable

Enable

<m>

Parameter shows the subscriber COLP service status in the network

COLP not provisioned

COLP provisioned

Unknown (e.g. no network, etc.)

<number>

Phone number in string type, format specified by

<type>

Type of address octet in integer format

129 Unknown type (IDSN format number)

145

International number type (ISDN format )

<subaddr>

String type sub-address of format specified by

<satype>

Type of sub-address octet in integer format (refer to 3GPP TS 24.008 sub clause

10.5.4.8 )

<alpha>

Optional string type alphanumeric representation of

<number>

corresponding to the

entry found in phone book

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands