Quectel UG Series Command Manual Download Page 119

Page: 119 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 118 / 247

9.5. AT+CMGD Delete Message

AT+CMGD deletes a short message from the preferred message storage

<mem1>

location

<index>

. If

<delflag>

is presented and not set to 0, then the ME shall ignore

<index>

and follow the rules of

<delflag>

shown as below.

Parameter

Example

AT+CMGD=1

//Delete the message specified in

<index>=1

AT+CMGD Delete Message

Test Command

AT+CMGD=?

Response

+CMGD:

(list of supported

<index>

s),(list of supported

<delflag>

Write Command

AT+CMGD=<index>[,<delflag>]

Response

TA deletes message from preferred message storage

<mem1>

location

<index>

If error is related to ME functionality:

+CMS ERROR:<err>

Maximum Response Time

300ms.

Note: Operation of

<delflag>

depends on the storage of

deleted messages.

Reference

3GPP TS 27.005

<index>

Integer type, in the range of location numbers supported by the associated memory

<delflag>

Delete the message specified in

<index>

Delete all read messages from

<mem1>

storage, leaving unread messages and

stored mobile originated messages (whether sent or not) untouched

Delete all read messages from

<mem1>

storage and sent mobile originated

messages, leaving unread messages and unsent mobile originated messages

untouched

Delete all read messages from

<mem1>

storage, sent and unsent mobile

originated messages, leaving unread messages untouched

Delete all messages from

<mem1>

storage

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands