Quectel UG Series Command Manual Download Page 129

Page: 129 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 128 / 247

Parameter

9.10. AT+CMGW Write Message to Memory

AT+CMGW write and execution commands store a short message from TE to memory storage

<mem2>

Memory location

<index>

of the stored message is returned. Message status will be set to "stored

unsent" by default, but parameter

<stat>

also allows other status values to be given.

The syntax of input text is same as the one specified in the write command

+CMGS

Read Command

AT+CMMS?

Response

+CMMS: <n>

Write Command

AT+CMMS=<n>

Response

ERROR

If error is related to ME functionality:

+CMS ERROR: <err>

Maximum Response Time

120s, determined by network.

Reference

3GPP TS 27.005

<n>

0 Feature disabled

Keep enabled until the time between the response of the latest message send command

(

+CMGS

+CMSS

, etc.) and the next send command exceeds 1-5 seconds (the exact value

is up to ME implementation), then ME shall close the link and TA switches

<n>

back to 0

automatically

Enable (if the time between the response of the latest message send command and the

next send command exceeds 1-5 seconds (the exact value is up to ME implementation),

ME shall close the link but TA will not switch

<n>

back to 0 automatically)

AT+CMGW Write Message to Memory

Test Command

AT+CMGW=?

Response

Write Command

1) If text mode (

+CMGF

=1):

AT+CMGW=<oa/da>[,<tooa/toda>[,<st

Response

TA transmits SMS message (either SMS-DELIVER or

SMS-SUBMIT) from TE to memory storage

<mem2>

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands