Quectel UG Series Command Manual Download Page 187

Page: 187 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 186 / 247

These parameters will not be saved.

12.6. AT+VTS DTMF and Tone Generation

The AT+VTS command is used to send ASCII characters which causes MSC to transmit DTMF tones to a

remote subscriber. This command can only be operated in voice call.

Parameter

Example

ATD12345678900;

Dial

AT+VTS DTMF and Tone Generation

Test Command

AT+VTS=?

Response

+VTS: (0-9,A-D,*,#),(0-255)

Write Command

AT+VTS=<dtmfstring>[,<duration>]

Response

ERROR

If error is related to ME functionality:

+CME ERROR: <err>

Maximum Response Time

Depends on the length of

<dtmfstring>

and

<duration>

Reference

3GPP TS 27.007

<dtmfstring>

ASCII characters in the set 0...9,#,*, A, B, C, D. The string should enclose in

quotation marks ("...")

When sending multiple tones at a time, the time interval of two tones

<interval>

specified by

+VTD

. The maximal length of the string is 31

<duration>

The duration of each tone in 1/10 seconds with tolerance

Value ranges from 0 to 255 and default is 0

If the duration is less than the minimum value depend on the network, the

actual duration is depend on the network

If this parameter is omitted,

<duration>

is specified by

+VTD

NOTE

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Related manuals for UG Series

Brands by name

Popular brands