background image

Chapter 5: DXi4500 Configuration

SNMP Configuration

Quantum DXi4500 User’s Guide

103

• To disable the Email Home Scheduler, clear the 

Enable Email 

Home Scheduler

 check box.

3

Specify the day and hour of the week when reports are sent.

4

Specify up to four e-mail recipients.

5

Click 

Apply

.

On Demand

Use the 

On Demand

 page to immediately send a Status Data or 

Configuration Data report to a recipient.

1

From the 

Email Home

 page, click the 

On Demand

 tab.

2

Select the type of report to send (

Status Data

 or 

Configuration 

Data

).

3

In the 

Send To

 box, specify the e-mail address where you want to 

send the report.

4

Click 

Send

.

SNMP Configuration

SNMP is short for Simple Network Management Protocol, a set of 
protocols for managing complex networks. SNMP works by sending 

messages, called protocol data units (PDUs), to different parts of a 

network. SNMP-compliant devices, called agents, store data about 

themselves in Management Information Bases (MIBs) and return this 

data to the SNMP requesters.
To access the 

SNMP

 page, from the 

Configuration

 menu, click the 

SNMP

 tab.

The 

SNMP

 page contains the following tabs:

Destinations

Community

Test

Summary of Contents for DXi4500



































































































































































































































Reviews: