quadient rena T-950 User Manual Download Page 15 | Manualshive

Page: 15 / 82

background image

ASSEMBLY AND INSTALLATION

15

3.

Install the front mounting screw.

4.

Connect the two motor cables to the base unit. The plugs are keyed to prevent improper
insertion.

Installing the Tab/Label Applicator Head

The Tabber comes with two Tab/Label applicator heads. The narrower head is used for tabbing
and stamp affixing. The wider head is used for labels over 2” wide up to 4” wide and Post-it

®

notes.

1.

Install the Applicator Head by sliding it
up into the cutout between the head
frame and the head-adjusting guide.
Attach the applicator head to the frame
using the two screws [4] supplied. The
mounting holes in the frame are oval
shaped. When installing the Applicator
Head it should be held in the upper most
position when tightening the screws. The
slots in the frame permit the head to be
mounted in a lower position for thin
media.

2.

Route the cable [5] toward the rear of the
machine and plug it in.
Attach the tab drive motor cable [6] and
the unwind/rewind drive motor cable [7]
at this time.

«
...
13
14
15
16
17
...
»

Summary of Contents for rena T-950



















































































Reviews:

No comments

Related manuals for rena T-950

Brand: National Vendors Pages: 42

Brand: Stilevs Pages: 20

Brand: Adcraft Pages: 9

Brand: Newco Pages: 8

Brand: Stalgast Pages: 8

Brand: Saeco Pages: 49

Brand: Printronix Pages: 150

FlexBrew Advanced 5-in-1

Brand: Hamilton Beach Pages: 36

Brand: Hendi Pages: 60

Brand: Royal Pages: 28

Brand: Flair Espresso Pages: 7

Brand: Hamilton Beach Pages: 24

Brand: tomado Pages: 64

Brand: Kompernass Pages: 20

Brand: MINIMOKA Pages: 28

Brand: Bartscher Pages: 44

Brand: Bartscher Pages: 62

Contessa Duo 190049

Brand: Bartscher Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands