quadient rena T-950 User Manual Download Page 19 | Manualshive

Page: 19 / 82

background image

SETUP & OPERATION

19

SECTION 3- Setup and Operation

The Tabber is capable of applying up to three tabs to the media in one pass. The steps required
to set-up the Tabber for applying tabs to the media are:

•

Install the proper Tab/Label Applicator Head in the machine

•

Align the Feeder.

•

Load tabs/stamps/labels

•

Adjust the Tabber for proper media transport

•

Program the Job

•

Run the Job

Changing the Tab/Label Applicator Head

The Tabber comes with two Tab/Label applicator heads. The narrower head is used for tabbing
and stamp affixing. The wider head is used for labels over 2” wide up to 4” wide and Post-it

®

notes.

1.

Raise the Head Assembly to its upper most position.

2.

Unplug the SENSOR connection from the rear of the
machine.

3.

Remove the sensor cable and gromet from the rear top
cover.

4.

Remove the two Allen screws that attach the Tab/Label
Applicator Head to the Head Assembly Frame, and then
remove the Tab/Label Applicator Head.

5.

Install the other Tab/Label Applicator Head in reverse
order. The Tab/Label Applicator Head should be held
in the upper most position when tightening the screws.
The lower position is for thin media and small tabs.

«
...
17
18
19
20
21
...
»

Summary of Contents for rena T-950



















































































Reviews:

No comments

Related manuals for rena T-950

Brand: Panasonic Pages: 44

Brand: Zelmer Pages: 144

Brand: Canon Pages: 285

PROFESSIONAL BELGIAN IB08WR119

Brand: Waring Pages: 16

Brand: Simonelli Pages: 192

Brand: BALAY Pages: 76

Intelia Deluxe HD8902

Brand: Saeco Pages: 56

Brand: Dash Pages: 32

BradyJet J20-PAD

Brand: Brady Pages: 2

ICE MASTER 110W

Brand: Mellerware Pages: 24

Brand: Salamander Pages: 2

Brand: Zojirushi Pages: 28

Brand: Hamilton Beach Pages: 12

Brand: Cornelius Pages: 2

Brand: Barazzoni Pages: 2

Espresso AC-755

Brand: Aircraft Pages: 9

Brand: Bella Pages: 24

Brand: Jenn-Air Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands