quadient rena T-950 User Manual Download Page 42

Page: 42 / 82

SETUP & OPERATION

Advanced Features

The

Advanced

features are available from the

Start-Up Screen. (If you are in another menu,
you can use the EXIT key (may need to press
more than once) to get back to the Start-up
Screen, shown to the right.

When the

Advanced

soft key is pressed.

The display will prompt you with the following
choices:



Sensor 1 –

Pressing this soft key will select

Media Sensor 1 (Front Sensor. Sensor
located closest to operator side of Tabber.).



Sensor 2 –

Pressing this soft key will select

Media Sensor 2 (Back Sensor. Sensor
located farthest away from operator side of
Tabber.).



More

– This soft key is used to access

additional Advanced features.

If the

More

soft key is pressed. The display will

prompt you with the following choices:



V-Tab

- This soft key is used to set the tab

sensor voltages for the tab/stamp material
you are using. See “Tab Sensor Setup” for
instructions.



Backlight

- This soft key is used to set the

backlight intensity for the LCD display.



More

- This soft key is used to access

additional Advanced features.



EXIT

– Brings you back to the Start-Up

Screen.

Sensor 1 is currently: Enabled
Choose: Sensor 1, or Sensor 2 to enable
Status: Advanced
Sensor 1 Sensor 2 More… EXIT

Press RUN to tab using Job 1.
Status: Pieces: 0
Mode Tab Jog Pass-Thru Advanced

Status: Advanced
V-Tab Backlight More… EXIT

Sensor 1 is currently: Enabled
Choose: Sensor 1, or Sensor 2 to enable
Status: Advanced
Sensor 1 Sensor 2 More… EXIT

Summary of Contents for rena T-950



















































































Search results

Summary of Contents for rena T-950

Reviews:

Brands by name

Popular brands

quadient rena T-950, User Manual

Search results

Summary of Contents for rena T-950

Reviews:

Brands by name

Popular brands