manualshive.com logo in svg

quadient rena T-950, User Manual

Share
Download
quadient rena T-950 User Manual Download Page 51

 

SETUP & OPERATION

 

 

 

51 

6.

 

Select the # 

2

 soft key to select two tabs. 

 
 
 
 
 
 
 
Press the 

Length

 soft key to set the media 

length. 
 
 
 
 
 
 
 

7.

 

Make sure the transport power button is on then 
press the 

Automatic

 soft key. 

If instructed to increase or decrease transport 
speed, do so until the message “Feed 1 Product 
now. Appears”. 
 
 
 

8.

 

Feed 1 Product (one piece of media).  
The Tabber will measure the media length and 
display this information.  
Verify that the measured length is accurate  
(+ or - 0.250” of actual piece length). 
Once you have an accurate measurement, you 
can press the 

EXIT

 soft key to proceed to the 

next step.  
 

Tip:

 If the Tabber measures the piece to be longer than the actual piece length; then more than one piece 

may have been fed, or the media may be slipping or hesitating as it feeds. Check/Adjust the transport 
system. 
If the Tabber measures the piece to be shorter than the actual piece length; then the media may not be 
feeding straight (missing the sensor), or a hole in the media may be traveling through the sensor, or the 
sensor may be getting reflection off the mail piece. If using a high gloss media; the sensor intensity may 
need to be adjusted lower, by a qualified Service Technician. 
If the media passes through without the Tabber providing a measurement; then the wrong media sensor 
may have been selected, or the media sensor may be dirty. Check to be sure the correct media sensor was 
selected. Try cleaning the sensor as described in this manual. 
These problems need to be corrected before the Tabber will function correctly.

 

 

9.

 

Press the 

Backing

 soft key. 

 
 
 
 

Select option to edit, or 
Press RUN to tab using Job 2. 
Status: Job Setup 
# Tabs       Length       Backing             EXIT

 

Enter piece length and press SAVE key 
0.0”                             Current value:  9.546” 
 
Automatic                                              EXIT 

Enter piece length and press SAVE key 
0.0”                             Current value:  8.523” 
Status:                                             Pieces: 1 
Automatic                                              EXIT 

Select option to edit, or 
Press RUN to tab using Job 2. 
Status: 
# Tabs       Length       Backing             EXIT

 

 

Press 1, 2 or 3 for the number of tabs. 
                                      Current value:  2 
 Status: Job Setup 
   1                  2                  3                    EXIT 

Summary of Contents for rena T-950



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands