quadient rena T-950 User Manual Download Page 67

Page: 67 / 82

TROUBLESHOOTING

SECTION 5 – Troubleshooting

The following trouble-shooting guide is provided to assist you in solving problems that might
occur with the Tabber.

Jams

CONDITION

SOLUTION

Media jams in transport section of Tabber.

Check alignment of Feeder to Tabber. Media
should be feed between 1/8” to 1/32” from
the Media Guide Fence in the Tabber.

Check that the two Media Hold-Down Guides
are not pressing down too firmly on the
media.

Check that the Registration Assembly is not
pushing the paper too tightly against the
Media Guide Fence. This can stall the media.

Transport pressure may be too tight.
Check/adjust Media Thickness Adjustment.

Tab Placement Problems

CONDITION

SOLUTION

Tabs are not placed in the same spot on
the media.

Tabs should be placed /- 1/8”
1.

Check/adjust the pitch setting for the tab. It
should be 0.010 more than the tab size plus
the space between the tabs.

Check to be sure the V-Tab adjustment is
correct for this stock.

Check Media Thickness Adjustment. Too
little transport pressure can cause the media to
slip when it is being fed.

Check that the pointer on the applicator head
is in the center of the tab.

Check to be sure the press roll, for tab drive,
is engaged. If this roller is not engage, the tab
drive roller will slip on the tab stock.

More of the tab is on the top of the media
than on the bottom.

Adjust the fine adjustment knob clockwise to
move more of the tab to the bottom side of
the media.

Summary of Contents for rena T-950



















































































Search results

Summary of Contents for rena T-950

Reviews:

Related manuals for rena T-950

Brands by name

Popular brands

quadient rena T-950, User Manual

Search results

Summary of Contents for rena T-950

Reviews:

Related manuals for rena T-950

Brands by name

Popular brands