manualshive.com logo in svg

quadient rena T-950, User Manual

Share
Download
quadient rena T-950 User Manual Download Page 14

 

ASSEMBLY AND INSTALLATION 

 

 

14 

SECTION 2 - Assembly and Installation 

The XPS-ProTab 4.0 is shipped in two cartons, on a single skid.  The Base unit is located below 
the Head Assembly.  Remove the carton, which contains the Head Assembly, from the top of the 
carton that contains the Base unit. Remove the cardboard carton from the pallet to expose the 
base unit. Next remove the Base unit from the pallet and place it on a stable floor surface. 
Remove the Head Assembly from its packaging material and follow the assembly instruction 
below. 

The T-950 is shipped in one carton, on a skid. Remove the cardboard carton from the palette, and 
then remove the Head Assembly from the packing material.  Next, remove the Base unit and 
place it on a flat working surface. Please follow the assembly instruction below. 

Installing the Head Assembly 

CAUTION 

The Head Assembly is heavy.  It is strongly recommended that two 

technicians install the Head Assembly of the Tabber to the base. 

1.

 

Place the open slot of the Head Assembly 
over the nylon bushing on the base unit.  
The Head Assembly has to be tilted at an 
angle to accomplish this. 

 

 

 

 

 

 

2.

 

Lower the head into position over the 
Head-adjusting guide.  There are two 
flats cut into the adjusting guide.  One at 
the top [1] and one on the left hand side 
[2].  The Head Assembly frame should 
rest in the top flat [1] and against the left 
hand flat [2].  When the head assembly is 
properly positioned, the two screws [3] 
that attach the Head assembly to the 
adjusting guide can be installed. 

 

 

 

Summary of Contents for rena T-950



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands