quadient rena T-950 User Manual Download Page 6

Page: 6 / 82

GETTING ACQUAINTED

Packaging/Shipping

The Tabber is shipped in appropriate packaging so that, under normal shipping conditions, it reaches its
destination without damage.

NOTICE:

Report damage to the carrier. The carrier is liable for any damage during transport. Transport

and storage should take place under normal conditions, i.e. at temperatures b5°C and +70°C and
relative air humidity of up to 80%. Exposure to conditions that are not permissible may lead to damage
which is not externally visible.

IMPORTANT

Please save the packaging materials for future use! It will be required if you ever need to

ship the Tabber.

Contents

The following items are included with your Tabber:

1 Operations Manual

1 Head Assembly

1 Tab Reel Side Guide

1 Take-up Reel Side Guide

1 Power Cord

1 2” Tab Applicator Head (for tabs/labels 2” wide or less)

1 4” Label Applicator Head (for labels over 2” wide, up to 4” wide, and Post-it

notes.)

1 Fan Folded Label Tray 1 (for labels 2” long or less)

1 Fan Folded Label Tray 2 (for labels over 2” long, up to 7” long)

1 Sample Roll of Tabs

Note: Additional Tabs can be purchased through your local Dealer/Distributor.

1 Feeder Interface Cable (Part #: 33E-500-192 rev A)
- For connecting the EasyFeed 120/140 Feeder to the T-950 Tabber

Summary of Contents for rena T-950



















































































Search results

Summary of Contents for rena T-950

Reviews:

Related manuals for rena T-950

Brands by name

Popular brands

quadient rena T-950, User Manual

Search results

Summary of Contents for rena T-950

Reviews:

Related manuals for rena T-950

Brands by name

Popular brands