manualshive.com logo in svg

quadient rena T-950, User Manual

Share
Download
quadient rena T-950 User Manual Download Page 33

 

SETUP & OPERATION

 

 

 

33 

Programming the Job (Menu Features)

 

 

Before you can run the Tabber, you must program the Tabber for the following: 

 

Media Sensor Selection (Sensor 1 or Sensor 2) 

 

Number of Tabs/Stamps/Labels you plan to apply to each piece. 

 

Media Length (When using Auto Tab/Stamp Positioning feature). 

 

Tab Offsets (When labeling and when not using the Auto Tab/Stamp Positioning feature). 

 

Backing Type (Clear or Opaque) 

 

Tab Pitch (Distance from top of tab/stamp/label, to top of next tab/stamp/label, plus 0.010”.) 

 

V-Tab (tab sensor voltage settings)

 

 

Start-Up Screen 

The 

Start-Up 

screen will appear when you turn the Tabber on.  

The soft keys at the bottom of the display control the following functions: 

 

Mode

 

 

 

 – 

Pressing this soft key will bring you to the mode selection screen, which allows you to 

select the tab/stamp positioning mode. See “Mode Features”.

 

 

Tab Jog

 

 

 

 – 

Pressing and holding this key will cause the tab drive roller to advance very slowly. 

 

 

Pass-Thru / Operate

 

 

 

 

– Pressing this soft key 

will cause the Tabber to toggle between the 
“pass-thru” mode and the “operate” mode.  
When 

Pass-Thru

 is showing, for this soft key, 

the Tabber is in the 

operate

 mode.  

The operate mode is used to tab pieces as they 
are fed through the system. 
When 

Operate

 is showing, for this soft key, the 

Tabber is in

 Pass-Thru

 mode. The pass-thru 

mode can be used during the setup process to 
check for correct material transport adjustments.  
The pass-thru mode is also useful if the Tabber is 
being used in-line with other equipment. This 
mode can be used to pass media through to the 
next device; if the customer doesn’t want to tab 
the job.

 

 

Advanced 

– Pressing this key will place the 

Tabber in the advanced mode.  This mode is used 
to select the Media Sensor, set the V-Tab (tab 
sensing values/voltages) and to access other 
advanced settings and test routines. See 
“Advanced Features”.

 

 
Press RUN for pass-thru mode. 
Status:                                       Pieces:  0 
Mode        Tab Jog       Operate     Advanced 

 

 
Press RUN to tab using Job 1. 
Status:                                       Pieces:  0 
Mode        Tab Jog    Pass-Thru     Advanced 

 
Press RUN to tab using Job 1. 
Status:                                       Pieces:  0 
Mode        Tab Jog    Pass-Thru    Advanced 

 

Summary of Contents for rena T-950



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands