Polycom Audio and Video Administrator'S Manual Download Page 81

Page: 81 / 136

Chapter 5 - Managing the System Remotely

5 - 9

Setting Up SNMP

The V500 system sends SNMP (Simple Network Management Protocol) reports to
indicate a total of 31 conditions, including the following:

•

All alert conditions found on the V500 system’s alert page

•

Details of jitter, latency, and packet loss

•

Low battery power is detected in the remote control

•

A system powers on after a long period powered off

•

Administrator logon is successful or unsuccessful

•

A call fails for a reason other than a busy line

•

A user requests help

•

A telephone or video call connects or disconnects

Downloading MIBs

In order to allow your SNMP management console application to resolve SNMP
traps and display text descriptions for those traps, you need to install Polycom
MIBs on the computer you intend to use as your network management station.

The MIBs are available for download from the V500 web interface.

To download the Polycom MIBs:

On a PC, open a web browser.

In the browser address line, enter the IP address of the system (for example,

http://255.255.255.255

) to go to the V500 web interface.

Go to

System Setup > Admin Settings > Global Services > SNMP

Click

Download MIB

and follow the onscreen instructions.

Summary of Contents for Audio and Video









































































































































Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands

Polycom Audio and Video, Administrator'S Manual

Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands