Polycom Audio and Video Administrator'S Manual Download Page 43

Page: 43 / 136

Chapter 3 - Configuring Network Use

3 - 23

Setting the Dialing Rules

If your system is connected to a private network and also to a public network, you
may need to specify the codes and prefixes necessary for dialing other systems.

To set the dialing rules:

Go to

System > Admin Settings > Global Services > Dialing Rules

Configure these settings:

Placing a Test Call

When you finish configuring the system, you can use one of the sample numbers
in the directory to test your setup.

To place a test call:

On the Place a Call

screen, select

Directory

Select

Category

Select

Sample Sites

and highlight a location.

Press

Call

on the remote control.

You can also find a list of worldwide numbers that you can use to test your V500 system at

www.polycom.com/videotest

Setting

Description

Always Dial Area
Code

Specifies that calls to sites in the same area code must include
the area code.

Dial 1+ for all USA
calls

Specifies that calls to systems in the United States must include
a “1” before the area code.

Summary of Contents for Audio and Video









































































































































Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands

Polycom Audio and Video, Administrator'S Manual

Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands