Polycom Audio and Video Administrator'S Manual Download Page 54

Page: 54 / 136

Administrator’s Guide for the V500 System

4 - 8

www.polycom.com/videodocumentation

Far site

Near site

Call connects

Near and far site are the same size

and appear side by side.

Near site presses PIP

Size of far site window increases.

Using in a Call

Far site presents to near site

Content, near site, and far site are displayed in

Dual Monitor Emulation mode.

Using Dual Monitor Emulation

With Dual Monitor Emulation, you see both near and far sites on one TV monitor in two
different views. During presentations, you see content and the near and far sites.

Setting Up

On the monitor’s setup menu, select the full-screen setting that
stretches the picture uniformly, without clipping.

On the TV Monitor screen:
1. If you are using a wide screen monitor, set Monitor to 16:9.

Otherwise, set Monitor to 4:3.

2. Select Dual Monitor Emulation.

Summary of Contents for Audio and Video









































































































































Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands

Polycom Audio and Video, Administrator'S Manual

Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands