Polycom Audio and Video Administrator'S Manual Download Page 113

Page: 113 / 136

Appendix - 1

Appendix

This appendix provides the following technical details about the V500 system:

❑

Cable Descriptions and Drawings

❑

Port Usage

❑

Q.850 Cause Codes

Cable Descriptions and Drawings

The following table gives information about the cables shipped with the system.

If you have the ISDN option, you can also attach a BRI cable. The part number for
this cable is 2457-08717-001 and the length is 20 ft.

The pin-outs for the standard cables are shown in the following drawings.

Cable

Maximum Approved
Length

Part Number Shipped

LAN cable

Orange RJ-45

100 ft (30 m)

2457-08343-001

12 ft (3.6 m)

Composite video cable

Triple RCA with S-video

2457-08674-001

6 ft (1.8m)

Summary of Contents for Audio and Video









































































































































Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands

Polycom Audio and Video, Administrator'S Manual

Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands