Polycom Audio and Video Administrator'S Manual Download Page 111

Page: 111 / 136

Chapter 7 - Diagnostics and General Troubleshooting

7 - 19

How to Contact Technical Support

If you are not able to make test calls successfully and you have verified that the
equipment is installed and set up correctly, contact Polycom Technical Support by
telephone or Internet as described below.

By Telephone

Before calling Polycom Technical Support, please have the following information
ready. We also suggest that you go to

System > System Information

so that you

will have the System Information screen showing when you call for help.

❑

Description of the issue – What is happening or not happening, and any
related events you may be able to notice.

❑

The 14-digit

serial number in the System Information screen (also present on

the bottom of the system).

Contact Polycom Technical Support at 1-800-POLYCOM.

By Internet

To contact Polycom Technical Support, go to

www.polycom.com/support

Enter the following information, then ask a question or describe the problem. This
information helps us to respond faster to your issue:

❑

The 14-digit serial number in the System Information screen (also present on
the bottom of the system)

❑

The software version in the System Information screen

❑

Information about your network

❑

Troubleshooting steps you have already tried

Summary of Contents for Audio and Video









































































































































Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands

Polycom Audio and Video, Administrator'S Manual

Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands