Polycom Audio and Video Administrator'S Manual Download Page 75

Page: 75 / 136

Chapter 5 - Managing the System Remotely

5 - 3

Room Monitoring with the V500 Web Interface

The Web Director feature within the V500 web interface allows administrators of
the V500 system to monitor a call or the room where the system is installed.

For security reasons, this feature can only be enabled on the local system by an
administrator.

To enable room monitoring:

Go to

System > Admin Settings > General Settings > Security

Select

Allow Video Display on Web

to allow the room to be viewed remotely.

To view a room:

On a PC, open a web browser.

In the browser address line, enter the system’s IP address (for example,

http://255.255.255.255

) to go to the V500 web interface.

Go to

System Setup > Utilities > Web Director

Perform any of the following tasks:

•

Place or end a call

•

View near and far sites

•

Adjust system volume settings

•

Mute and unmute the microphone

Summary of Contents for Audio and Video









































































































































Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands

Polycom Audio and Video, Administrator'S Manual

Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands