Polycom Audio and Video Administrator'S Manual Download Page 110

Page: 110 / 136

Administrator’s Guide for the V500 System

7 - 18

www.polycom.com/videodocumentation

System Lights

The system lights are located on the front of your V500 system.

Network Interface Lights

The BRI network interface lights are located on the back of the system near the BRI
connector.

When the V500 system...

It means...

Indicators are off

No power to the system.

Green indicator blinks slowly

The system is sleeping.

Green indicator flashes when you
use the remote control

The system is not in a call, and is receiving
signals from the remote control.

Amber indicator flashes when you
use the remote control

The system is in a call, and is receiving signals
from the remote control.

Green indicator is on

The system is ready to make a call.

Amber indicator is on

The system is in a call.

Red indicator is on.

The system microphone is muted.

When the BRI network interface...

It means...

Indicators are off

•

No power to the system, or

•

The system is not connected to the network, or

•

The system is not receiving a clock signal from
the network, or

•

The system is restarting.

Green indicator is on

The system is receiving a clock signal from the
network.

Yellow indicator is on

The system is able to make a call.

Green and yellow indicators are on

•

The system is receiving a software update, or

•

The system is operating normally.

Summary of Contents for Audio and Video









































































































































Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands

Polycom Audio and Video, Administrator'S Manual

Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands