Polycom Audio and Video Administrator'S Manual Download Page 80

Page: 80 / 136

Administrator’s Guide for the V500 System

5 - 8

www.polycom.com/videodocumentation

Requesting Technical Support from the Global Management System

Administrator

You see the following message:

Tech Support will be alerted to phone you at the
following number. Continue?

Enter your contact telephone number.

The V500 system sends your information to the
Global Management System administrator.

You see the following message:

Tech Support has been alerted. You can also call
this number for assistance.

The message displays the telephone number you
entered for Tech Support on the My Information screen.

The Global Management System
administrator opens the alert
message containing your telephone
number.

Global Management System sends
a message to your V500 system.

The Global Management System
administrator calls you.

The V500 system displays the message from Global
Management System:

Your request for help has been acknowledged.

1. From the Place A Call screen, press

on the remote.

2. Select Support and press

on the remote.

Summary of Contents for Audio and Video









































































































































Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands

Polycom Audio and Video, Administrator'S Manual

Search results

Summary of Contents for Audio and Video

Reviews:

Related manuals for Audio and Video

Brands by name

Popular brands