Pioneer XY-122 Installation Manual Download Page 59

Page: 59 / 92

5 Drive unit replacement

__________________________________________________________________________________________________________

Replacement of LF drive unit

(1)

(2)

(3)

(4)

(5)

(6)

(7)

Additional information (XY-81/101)

CAUTION: The locations of the terminals on XY-81 and XY-101 are
different. Please see the locations of each drive unit in the figures
below when installing the LF drive unit.

Tighten the socket head bolts on the LF drive unit.

Tighten the bolts to ensure a solid fit to the grille.

For the connection information, please refer to following circuit diagram.

Reinstall the LF drive unit to the enclosure.

LF driver units installed in XY-81 and XY-101 are different, but
almost the same procedures can be used to replace both LF drive
units.

Remove the socket head bolts from the LF drive unit.
The number of socket head bolts to be removed from XY-81 is 8 and
from XY-101 is 4.

Ensure that the terminals of the drive unit are placed as shown
below.

Lift the LF drive unit up and remove the cables from the LF drive
unit.

Replace the LF drive unit with a new one.

Connect the cables to the two terminals.

Red Terminal (+)

Brown cable

Black Terminal (-) :

Blue cable

XY-81

XY-101

Location of terminals

Black terminal

Red terminal

Location of terminals

Blue cable

Brown cable

http://pioneerproaudio.com/

Page 59 / 92

Summary of Contents for XY-122



















































































Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands

Pioneer XY-122, Installation Manual

Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands