Pioneer XY-122 Installation Manual Download Page 8

Page: 8 / 92

2 Accessories

WARNING

・

Rigging should only be carried out by experienced personnel following safe working practice.

・

A safety steel can then be attached to this and connected to your safety point.

Hardware standby

Caution

・

Please follow an instruction manual for a commercially available product for installation and safety measures.

Accessories List

・

If you use any commercially available eyebolt, ensure it is the same size as in the list below and have enough

strength to withstand the weight of the loudspeaker.

All the supplied accessories for XY series are listed in the following "Accessories List".

(see Table 2-1 and 2-2 "Accessories List")
Please ensure that you read "Section 1: Introduction" and "Section 3.1 - 3.2" fully, and have the product installed by
a professional.

Have the installer carefully follow the installation instructions.

・

Check to make sure that any commercially available mounting hardware used is enough to support the

weight of the speaker system.

The overhead suspension of loudspeakers is a very serious issue with potentially lethal consequences should
anything go wrong.

When utilising any suspension method,

a secondary safety feature must be used.

For any suspension method, fit an

eyebolt to any of the rigging points.

The following hardware is provided with the XY series products so that commercially-available poles, brackets and
other items can be attached.

(see Table 2-1 and 2-2 "Hardware standby")

Should you be in any doubt whatsoever, please contact the retailer or dealer from which you purchased this
product.

Model Bolt size

Length

[mm]

Pitch

[mm]

Effective

length [mm]

Safe working load limits

[kN] ([kg])

XY-81
XY-101
XY-122
XY-152
XY-3B

0.785 (80.0)

M10

1.47 (150.0)

1.25

1.5

10 ~ 15

http://pioneerproaudio.com/

Page 8 / 92

Summary of Contents for XY-122



















































































Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands

Pioneer XY-122, Installation Manual

Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands