Pioneer XY-122 Installation Manual Download Page 79

Page: 79 / 92

6 Specifications

6.1 Spec sheet

The specifications and design of this product are subject to change without notice.

Suggested Power
Amplifier

Recommended : X4

Accessories

—

Enclosure

15 mm (0.6 inch) birch plywood

Polyurethane

Finish

Impact-resistant, Black semi-matt
textured

Black semi-matt textured

Rigging and Hardware

9 x M10 threaded mounting points ( 4 top /
1 bottom / 4 rear)
7 x flush handles (2 top / 2 left / 2 right / 1
rear)

1 x ø13 mounting hole on yoke

Grill

Hex punched steel

—

Dimensions (WxHxD)

530 mm x 1080 mm x 540 mm
(20.7 inch x 42.5 inch x 21.3 inch)

480 mm x 480 mm x 376 mm
( Not including the mounting yoke )

Weight

58.0 kg (127.9 lb)

13.5 kg (29.8 lb)

Crossover

MHF: Asymmetric internal passive
crossover

Asymmetric internal passive crossover

Connector

2 × Neutrik SpeakON™ NL4MD-V

Dispersion

50°H x 35°V

Driver Configuration

LF: 2 x 12 inch (305 mm) neodymium cone
driver, MF: 8 inch (203 mm) neodymium
MF cone driver, HF: 1.0 inch (25 mm) exit
neodymium compression driver

MF: 8 inch (203 mm) neodymium MF cone
driver,
HF: 1.0 inch (25 mm) exit neodymium
compression driver

Power Handling

LF: 1200 W RMS, 2400 W Program
MHF: 200 W RMS, 400 W Program

200 W RMS, 400 W Program

Maximum SPL

LF: 133 dB cont., 139dB peak
MHF: 130dB cont. , 136 dB peak

130 dB cont., 136 dB peak

Sensitivity (1w/1m)

LF: 102 dB
MHF: 107 dB

107 dB

Nominal Impedance

LF: 4Ω
MHF: 8Ω

8Ω

Enclosure Type

Three-way bi-amp loudspeaker

Two-way mid-high loudspekaer

Frequency Response

55 Hz to 17 kHz

170 Hz to 17 kHz

Product Name

XY-3B
XY-3B-W

XY-2

http://pioneerproaudio.com/

Page 79 / 92

Summary of Contents for XY-122



















































































Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands

Pioneer XY-122, Installation Manual

Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands