Pioneer XY-122 Installation Manual Download Page 24 | Manualshive

Page: 24 / 92

background image

3 Rigging And Caster Setting

__________________________________________________________________________________________________________

3.2.2 Horizontal Flying Cradle & XY-2

Table.3-2-2-A: Models compatible with respective Horizontal Flying Cradles

Table.3-2-2-B: Installation to the ceiling and wall

Using the Horizontal Flying Cradle, suspension of the XY-81/101/122/152
enclosure horizontally from the ceiling or the wall as shown in the right figure
is available.
Also, using the included yoke, suspension of the XY-2 from the ceiling, wall,
and bottom of XY-3B is available.
The orientation of the enclosure can be changed at any angle.

Several holes on both sides of the outer yoke of the cradle are used to change
the length of the outer yoke so that the distance between the enclosure and
the cradle can be adjusted. The factory default sets the distance between the
enclosure and the cradle at the nearest position. If you want to connect a
speaker cable and incline the enclosure, please select a different hole on the
outer yoke to enlarge the distance.

Speaker models compatible with respective Horizontal Flying Cradles are
shown in the table below.

Note:

The dispersion orientation when placing the XY-81/101/122/152

enclosure horizontally will be changed from the orientation when placing it
vertically. Rotate the horn inside of the enclosure to reverse the dispersion
orientation to the original orientation when it is placed vertically. Also, the
location and the orientation of the logo badge can be changed. (See "3.1.2
Horn rotation" and "3.1.3 Logo badge replacement")

To the ceiling

To the wall (Horizontal)

To the wall (Vertical)

NOTE: XY-122 is shown in the illustration.

No.

Use model

CP-XY8HC1

XY-81

CP-XY10HC1 XY-101
CP-XY12HC1 XY-122
CP-XY15HC1 XY-152
Not needed

XY-2

Vertical

Horizontal

CP-XY8HC1

Available

Available

Available

CP-XY10HC1

Available

Available

Available

CP-XY12HC1

Available

Installation

prohibited

Available

CP-XY15HC1

Available

Installation

prohibited

Available

XY-2

Available

Installation

prohibited

Available

Installation to the

ceiling

Part number

Installation to the wall

http://pioneerproaudio.com/

Page 24 / 92

©2018 Pioneer DJ CORPORATION

«
...
22
23
24
25
26
...
»

Summary of Contents for XY-122





























































































Reviews:

No comments

Related manuals for XY-122

Brand: Quadro Pages: 12

Brand: Magellan Pages: 2

Brand: Ultimate Ears Pages: 3

AeGIS 8000 Series

Brand: PACH & COMPANY Pages: 32

Brand: YA Pages: 14

Brand: Waterfall Audio Pages: 2

Brand: usi Pages: 10

Brand: Patlite Pages: 38

Brand: Labkotec Pages: 19

Brand: Bose Pages: 44

Brand: Electro-Voice Pages: 4

Brand: Heco Pages: 68

Brand: K&F Pages: 38

Brand: JBL Pages: 2

FWS222 BBE PLUS

Brand: Opro9 Pages: 16

Brand: 4CR Pages: 7

Brand: Martin Audio Pages: 1

Brand: basIP Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands