Pioneer XY-122 Installation Manual Download Page 76

Page: 76 / 92

5 Drive unit replacement

___________________________________________________________________________________________________________

5.3.3 XY-218HS

Part list

Item Part Name

Qty

Service Part No.

Required tools

Drive unit

PT-XY118SL1

・

5mm hex key

M6 socket head bolt

06G003

Spring washer

06D0075

M6 socket head bolt

06G003

Spring washer

06D0075

Flat washer

06D006

Procedure (XY-218HS)

Removing and reinstalling the door.

(1)

(2)

(3)

Replacement of LF drive unit

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

Lift the LF drive unit up, and remove the cables from the LF drive
unit.

Note

M6 x 40mm (P=1.0)
5mm hex socket head

Door

M6 x 40mm (P=1.0)
5mm hex socket head

Remove twelve socket head bolts from a door.

Take the door off the enclosure.

Reverse the above steps when placing the door back to the
enclosure. The door should be placed back in the same direction
before it was removed.

Remove eight socket head bolts from the drive unit.

Tighten the socket head bolts on the LF drive unit.

Tighten the bolt to ensure a sodoor fit to the door.

Replace the LF drive unit with a new one.

Connect the cables to the two terminals.

Red Terminal (+)

: Black cable with a white line

Black Terminal (-) : Black cable

Ensure that the terminals of the drive unit are placed as shown
below.

Reinstall the LF drive unit to the enclosure.

Red Terminal

Black Terminal

Location of

terminals

Front

Back

http://pioneerproaudio.com/

Page 76 / 92

Summary of Contents for XY-122



















































































Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands

Pioneer XY-122, Installation Manual

Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands