Pioneer XY-122 Installation Manual Download Page 53

Page: 53 / 92

4 System Configuration

____________________________________________________________________________________________________________

Loudspeaker connections

The XY Series are supplied as standard with Neutrik SpeakON™ NL4 connectors, wired pin 1+/1– and 2+/2-.

Pin 2+/2- is used for mid-high drivers in the XY-3B, and in the other models used for only link-through.

It is recommended that the resistance of your cable be less than one tenth of the nominal system impedance.

Given below are the recommended maximum cable lengths for different cross-sections and impedances.

4.0mm

44m

88m

176m

6.0mm

66m

132m

264m

2.0mm

22m

44m

88m

2.5mm

29m

58m

116m

1.0mm

11m

22m

44m

1.5mm

17m

34m

68m

WARNING: Ensure that cables are compatible with both the specifications of the Power Amplifier

and Speaker used.
Using wrong pinouts may cause damage to the speakers or cause accidents.

Conductor Cross Sectional Area

Maximum Recommended Cable Length

4 Ω

8 Ω

16 Ω

XY-115S / 118S

XY-215S / 218S / 218HS

XY-81 / 101 / 122 / 152

XY-3B

MHF

XY-2

http://pioneerproaudio.com/

Page 53 / 92

Summary of Contents for XY-122



















































































Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands

Pioneer XY-122, Installation Manual

Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands