Pioneer XY-122 Installation Manual Download Page 58

Page: 58 / 92

5 Drive unit replacement

__________________________________________________________________________________________________________

(4)

Only XY-81

(5)

(6)

(7)

Connect the cables to the two terminals.

Replace the HF drive unit with a new one and tighten the socket
head bolts or nuts.

NOTE: Ensure that the packings are firmly attached to the slits using
elastomeric adhesive, otherwise sound quality may be deteriorated.

Install the HF waveguide to the enclosure.

Tighten the four socket head bolts on the HF waveguide.
Make sure to place the HF waveguide in the same orientation as
before replacing the drive unit.

White cable

Yellow cable

Red Terminal (+) :

Black Terminal (-) :

Only XY-81

Only XY-101

http://pioneerproaudio.com/

Page 58 / 92

Summary of Contents for XY-122



















































































Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands

Pioneer XY-122, Installation Manual

Search results

Summary of Contents for XY-122

Reviews:

Related manuals for XY-122

Brands by name

Popular brands