+12V
DC
Brown
Ground When Running
INPUT
(-)
Black
Chassis Ground
INPUT
(-)
Right Sliding Door (See Wire Guide)
INPUT
(-)
Blue
Unlock
INPUT
(-)
Green
Lock
INPUT
(-)
Pink
Left Sliding Door (See Wire Guide)
INPUT
(-)
Pink/White
Door Sense Trigger
(-)
Violet/White
Doorlocks/Alarm Activation ( See Wire Guide)
OUTPUT
(-)
Violet
DATA
Data
Red
(+)12 Volt Constant
INPUT
(+)
See Wire Connection Guide for detailed information regarding wire functionality
Section A
Programming Button
“Fig. 1”
Diagnostic plug
(Face view)
10 PIN HARNESS
Legend RCS = Remote Control System
N/C =
No Connection N/A = Not Applicable W2W= analogue wire to wire D2D= data 2 data
(-)
/(+)
(-)
VEHICLE
TYPE
Input
Input
Input
Input
Input
Input
Data
(-)
WIRE
COLOR
Brown
Green
Blue
Violet/
White
Violet
Pink/
Whi te
Pink
Orange
Red
Black
(-)
(-)
(+)
SPECIFIC WIRE CONNECTION LOCATION
Connector C3 on BCM (Left side of steering column near
firewall on)
AUX Output for Right Sliding Door
Constant (+) 12 Volt Source
Chassis Ground
Connect
Location
RCS
RCS
RCS
Vehicle
Vehicle
Vehicle
(-)
ACTIVATION and/or FUNCTIONALITY
Factory Alarm Arm/ Disarm
Lock All Doors
Unlocks All Doors
Activates Doorlocks and Alarm
(See Fig.3)
RCS
N/A
N/A
N/A
Type 1
(2001-2003
Minivans)
N/A
N/A
N/A
N/A
Power Source
Ground Source
WIRE GUIDE: CONNECTIONS
Section B
On Board Diagnostic Connector (OBDII) PIN 2
Face View Under Dash on Driver Side
(See Fig.1)
Data Commands from Module to Vehicle
AUX Output for Left Sliding Door
1 sec (-) Pulse Lft Slide Door Open/Close
PIN#
1
2
3
4
5
6
7
8
9
10
Ground When Running Output of Remote Starter
Input
(-)
RCS
Output (-)
RCS
Output (-)
Vehicle
Orange
OUTPUT
Type 1 & 2
1 sec (-) Pulse Right Slide Door Open/Close
Trunk or AUX Output
D2D
w2w
Type 1 & 2
With Factory Alarm = Purple/Lt Blue
(PIN14)
Without Factory Alarm = Purple/Drk Green
(PIN21)
3 sec (-) Pulse Releases Trunk/Rear Hatch
OR
1 sec (-) Pulse simultaneously on Orange & Pink Releases
Trunk/Rear Hatch
(See Fig.2)
Detects Doors status (open/closed) via data bus then
converts to an analogue output (-)
“Fig. 3”
C3
Type 1 & 2
Input
(-)
RCS
I/O
STATUS
Pink
Orange
Remote starter
Trunk out
Diode
*NOTE: Power Lift Hatch
(AUX OUTPUT)
(AUX OUTPUT)
“Fig. 2”
Connect to (-) door trigger input wire of RCS
Connect to (-) Unlock Output wire of RCS
Connect to (-) Lock Output wire of RCS
LED
UPGRADEABLE
DOOR LOCK
&
OEM ALARM
INTERFACE
MODULE
1
0
P
I
N
H
A
R
N
E
S
S
D2D = Optional use of 4 Pin Data to Data (D2D) cable will replace the analogue wire (w2w) connection
D2D
w2w
D2D
w2w
D2D
w2w
w2w
w2w
D2D
w2w
D2D
w2w
D2D
w2w
D2D
w2w
D2D
w2w
D2D
w2w
IMPORTANT!
Please read this installation guide thoroughly before installing. Use only a high quality digital multi-meter for testing. This product connects to the vehicle's low voltage signal
wire and improper installation or testing can result in damage to the vehicle. Never use a test light or logic probe to test wires in this vehicle!
Platform # 03 Firmware: CHDL6+
Description:
Caravan/Pacifica Door Lock Alarm Interface (NO KEY REQUIRED)
Functions:
Data Bus Interface: Lock/Unlock, Trunk/Rear Hatch, Sliding Door RT. & LEFT, OEM Security, Arm/Disarm, Starter Enable,
Door Pin Status Output for Aftermarket Alarm (-)
Installation
Manual
(1\2 Pages)
