12
<DRC1285>
En
1. Installation
2. Connections
3. Power ON/OFF
4. Control
5. Transporting Unit
6. Error Correction
÷
Do not place foreign objects inside the changer, since malfunction
may result.
÷
Do not use the changer in locations subject to high concentrations
of dust, heat, or humidity.
* Do not install in locations directly exposed to outdoor dust or air.
* Do not install near air conditioner vents or air cleaners.
÷
Do not subject the recorder to impact or vibration during use.
* Do not install in hallways or other areas near frequent pedestrian
traffic.
÷
When connecting exterior SCSI cable, be sure that power is first
turned off to host computer and changer.
* When connecting internal SCSI cable, power may be left while
connecting.
÷
When installing a drive, be sure to connect the changer interface
cable to the connector corresponding to the bay in which the drive
is installed. If the cable is mistakenly connected to a neighboring
connector, the discs may be damaged and the
E99
error may occur.
÷
The final device on a SCSI bus must have its terminator switched
ON, or an external terminator device used. The changer may oper-
ate erratically if proper termination is not provided. If no termination
is used and malfunctions occur, turn termination on before restoring
power to the changer.
* If the final device on a SCSI bus (with terminator turned ON) is
removed from the bus, or if its SCSI cable is disconnected, it means
that bus termination is not provided from that time, and the same
kind of malfunctions may occur as described above.
÷
When installing a drive, if the wiring monitor indicator does not flash,
recheck and install the power cable connection, followed by the
changer interface connection.
÷
Never disconnect power while the changer is transporting a disc, or
when the writer is recording data to a disc.
÷
When turning the power off and then on again, wait at least ten
seconds after turning the power off before turning it on again.
÷
During data recording, do not send commands from the disc writer
to remove disc (
Move Medium, Rezero Unit
), since
EC
❋
error or
write malfunction may occur (back buffer underrun).
÷
When transporting the unit, pack the unit in its original packaging
materials, and ship in an upright position. Do not transport the unit
on its side.
÷
Do not transport the unit with drive units, 50-disc magazines or other
optional accessories loaded (except for 20-disc hyper-magazine).
When transporting the accessories, repack them in their original
packaging materials.
÷
Do not transport disc magazines with discs loaded.
÷
E8
❋
,
E9
❋
,
EF8
, or
EF3
errors cannot be corrected merely by reset-
ting the changer’s power on/off. The system administrator mode
must be used to open and then close the door again. For these and
other errors, see the Operating Instructions, p. 46.
÷
[
E83
], [
E99
], [
E88
]
÷
Recording/playback mal-
function
÷
Recording/playback mal-
function
÷
Changer malfunction
÷
[
E83
], [
E99
]
÷
Display window (LCD)
doesn't appear correctly.
÷
Operation keys malfunc-
tion.
÷
Changer not recognized
on the SCSI.
÷
Changer does not detect
drive.
÷
Changer malfunction.
÷
Data recording malfunc-
tion
÷
Recording malfunction
÷
[
EC
❋
], (where
❋
=
0
–
F
)
÷
[
E8
❋
], [
E9
❋
], [
EF8
], [
EF3
]
(where
❋
=
0
–
F
)
TO AVOID PROBLEMS
The following is a list of operation items that may potentially lead to problems in component functioning.
Potential Malfunction/Error
Issue
Summary of Contents for DRM-300
Page 2: ...2 DRC1285 En ...
