41
Safe Handling of Gas Cylinders
Web address:
www.perkinelmer.com/WEEE
For Customer Care telephone numbers select "Contact us" on the web page.
Products from other manufacturers may also form a part of your PerkinElmer
system. These other producers are directly responsible for the collection and
processing of their own waste products under the terms of the WEEE Directive.
Please contact these producers directly before discarding any of their products.
Consult the PerkinElmer web site (above) for producer names and web addresses.
Safe Handling of Gas Cylinders
Gases commonly used with ICP instruments include argon and nitrogen. The major
hazard associated with these gases is suffocation. This can occur if the gas is
allowed to escape in an enclosed area and displaces the oxygen in the air. These
gases are neither explosive nor combustible.
Note
The permanent installation of gas supplies is the responsibility of the user
and should conform to local safety and building codes.
Contact the gas supplier for a material safety data sheet (MSDS)
containing detailed information on the potential hazards associated
with the gas.
Carefully use, store, and handle compressed gases in cylinders. Gas
cylinders can be hazardous if they are mishandled.
Avertissement:
Contactez le fournisseur du gaz afin d'obtenir une fiche
de sécurité de produit (MSDS) contenant des informations détaillées sur
les dangers potentiels associés au gaz.
Soyez prudent lorsque vous utilisez, stockez et manipulez des gaz
comprimés en bouteilles. Les bouteilles de gaz peuvent être dangereuses
si elles ne sont pas manipulées correctement.
!
Warning
!
Summary of Contents for AVIO 200
