manualshive.com logo in svg

PerkinElmer AVIO 200, Hardware Manual

Share
Download
PerkinElmer AVIO 200 Hardware Manual Download Page 104

Installation

102

Connecting the Argon Supply

Use the following procedure to connect the argon supply.

1. Connect the instrument to the argon supply using the argon hose (Part No. 

N0690274), uses a 1/4-in. Swagelok fitting) using a 1/4-in. space collar (Part No. 

09920125) on both ends of the tubing.

2. Set the argon supply regulator between 550 kPa and 825 kPa (5.5 to 8.25 bar or 

80-120 psig).

3. Check for leaks using a proprietary leak testing fluid for high purity gas lines.

Connecting the Shear Gas Supply

The shear gas used is typically compressed air; however, nitrogen may also be used. 
The shear gas must be clean and dry, so the instrument includes an air dryer filter 
assembly (Part No. N0775325) and is included in the Installation kit (Part No. 
N0790432). For more information on the requirements for the shear gas supply, refer 
to 

Pneumatic Requirements 

on page  66. 

An air hose (Part No. N0770348) with 1/4-in. Swagelok fittings at each end, is 
supplied in the hose kit that is shipped with the instrument. A second air hose is also 
included. The following procedure describes how to connect the PerkinElmer air 
compressor, filter and regulator. 

Caution

Attention

Gas delivery lines from the argon tank must be contaminant-free and not made of 
plastic, although PTFE lines are acceptable.

Des lignes de distribution de gaz à partir du réservoir d'argon doit être exempt de 
contaminants et non pas en matière plastique, bien que des lignées de PTFE sont 
acceptables.

Note

f you are using house air, it must be clean and dry. The instrument includes 
an air dryer assembly (Part No. N0775325). Refer to 

Connecting the 

Shear Gas Supply

 later in this chapter.

Summary of Contents for AVIO 200






















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands