manualshive.com logo in svg

Pentair EASYTOUCH PL4, User Manual

Share
Download
Pentair EASYTOUCH PL4 User Manual Download Page 75

 

 

EASYTOUCH

® 

PL4/PSL4 Control Systems User’s Guide

 

 

  67

 

Synchronizing control panels

If the EasyTouch

®

 PL4/PSL4 Control System Outdoor Control Panel was previously setup with specific pool 

and spa information and an additional indoor or wireless control panel with factory default information is 
installed, during the installation process the outdoor control panel will automatically download the system 
information to the connected control panel. If the outdoor, indoor or wireless control panels have different 
revision levels or contain previous setup information, you can choose which system image to upload or 
download.
Synchronizing control panels is initiated from the indoor or wireless control panel. The following describes how 
to synchronize an indoor or wireless control panel. 

Download from outdoor control panel to indoor control panel

• 

Press the 

Menu

 button to download the system image from the EasyTouch PL4/PSL4 Control System outdoor 

control panel. 

Upload to outdoor from indoor control panel

1.  Press the 

Up/Down

 button to access the “Upload” screen. 

2.  Press the 

Menu

 button to upload the system image from the indoor or wireless control panel to the EasyTouch 

PL4/PSL4 Control System outdoor control panel. 

Note:

 To erase existing control panel system information, use the “Erase EEPROM” feature. Refer to “Erase 

EEPROM” on page 52 for more information.

Wiring UltraTemp

®

 Heat Pump to EasyTouch PL4/PSL4 Control System

Be sure to check the UltraTemp Heat Pump terminal block wire colors and pinouts (located on the back of 
the Auto Set board) before connecting it to the EasyTouch PL4/PSL4 Control System COM port on the main 
circuit board. The See the wiring table below for the pin configuration.  For UltraTemp Heat Pump setup 
information, see page 41.

IMPORTANT: On the UltraTemp Heat Pump AutoSet board ONLY CONNECT PIN 3 (YELLOW) 
and PIN 2 (GREEN) to the EasyTouch PL4/PSL4 Control System COM port pins YELLOW and 
GREEN respectively. Do not use pin 1 or pin 4 on the AutoSet board or the EasyTouch PL4/
PSL4 Control System main circuit board. These pins are not used.

Wiring Description

EasyTouch PL4/PSL4 
Control System 
COM port wire color

Description

UltraTemp Heat Pump 
pin number and wire color

PIN 4 (RED) 

NOT USED

+15 VDC

PIN 4 (RED) NOT USED

PIN 3 (YELLOW)

+ DATA

PIN 3 (YELLOW)

PIN 2 (GREEN)

- DATA

PIN 2 (GREEN)

PIN 1 (BLACK) 

NOT USED

GROUND

PIN 1 (BLACK) NOT USED

 Unit Mismatch                

  Download from

       Outdoor 

 

 Unit Mismatch                

     Upload to

       Outdoor 

 

Summary of Contents for EASYTOUCH PL4

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands