Pentair EASYTOUCH PL4 User Manual Download Page 63

Page: 63 / 80

EASYTOUCH

PL4/PSL4 Control Systems User’s Guide

Diagnostics Menu: Self Test

Tests the control panel LCD and buttons. Follow the on-screen prompts to perform the tests.

MENU

DIAGNOSTICS

SELF TEST

Note: If the Indoor Control Panel is connected to the EasyTouch PL4/PSL4 Control System outdoor control
panel, select “LINK CLOSED” in the UART test to abort the UART test. This allows the test to complete with
and display PASSED.

Press the

Right

button to display the current software and boot loader revision levels

for the outdoor control panel.

Press the

Right

button to start the test:

Press the Right button to start the test:

Display Test:

Press any button to start the LCD test.

Backlight Test:

Press the

Left

then

Right

button.

Contrast Test:

Press any button to continue.

LED Test:

Press any button to continue. All of the button LEDs will be tested.

Switch Test:

Press any button to continue. As prompted, press the appropriate

buttons.

UART Test:

Select “LINK CLOSED” to abort this test if the optional Indoor Control

Panel is connected to the system Power Center.

Status: Passed - Code 0:

After you have completed the test

an error code

is displayed. “Passed” is displayed if the test was successful. For error code
descriptions, see “Self Test Error Codes,” on page 59.
Press the

Menu

button to return to the Settings menu options. Press the button again

to return to the main menu options or press again to return to the main screen.

Diagnostics Menu: Bootloader Rev

Displays the current bootloader revision for the indoor control panel and the main EasyTouch PL4/PSL4
Control System control panel.

MENU

DIAGNOSTICS

BOOTLOADER REV

UIC:

Displays the current bootloader revision level for the indoor control panel.

UOC:

Displays the current bootloader revision level for the outdoor control panel.

Press the

Menu

button to return to the Settings menu options. Press the button again

to return to the main menu options or press again to return to the main screen.

Backlight On

<=Backlight On

>=Backlight Off

Contrast:

Press any button

LED Test

Switch Test

Press any button

UART Test

<=Link Closed

>=Link Open

Press Any Button

Firmware Version
Soft: 2.130
Boot: 2.130
Press Any Button

Bootloader Rev

UIC: 1.02

UOC: 1.02

Summary of Contents for EASYTOUCH PL4

















































































Search results

Summary of Contents for EASYTOUCH PL4

Reviews:

Brands by name

Popular brands

Pentair EASYTOUCH PL4, User Manual

Search results

Summary of Contents for EASYTOUCH PL4

Reviews:

Brands by name

Popular brands