manualshive.com logo in svg

Pentair EASYTOUCH PL4, User Manual

Share
Download
Pentair EASYTOUCH PL4 User Manual Download Page 55

 

 

EASYTOUCH

® 

PL4/PSL4 Control Systems User’s Guide

 

 

  47

 

Settings Menu: 2-Speed Pump

Equipment circuits selected in this menu will automatically switch a two-speed filter pump to high speed when 
these circuits are on. If a two-speed pump is assigned to solar, a cleaner or a pump, when activated the pump 
will automatically run for five minutes in high speed then switch to low speed.  For example, when on, the 
filter pump will switch to high speed whenever the JETS or CLEANER is on. There must be a two-speed relay 
installed in the EasyTouch PL4/PSL4 Control System Power Center in order for the “2-Speed Pump” menu 
settings to function. 

 
2-Speed Pump

To configure a two-speed pump to a circuit:

MENU

s

SETTINGS

s

2-SPEED PUMP

w

2-SPEED PUMP

 

Settings Menu: Solar

Use the solar settings to setup solar or configure solar as a heat pump: 

Setting Up Solar Control

: Ensure 

that the solar temperature sensor is installed.

About Installing Solar Heating: 

First, install the solar sensor at the collectors and connect to the EasyTouch 

PL4/PSL4 Control System Power Center. If HEAT PUMP is selected and is being used in place of a solar 
heating system, install Solar sensor near the EasyTouch PL4/PSL4 Control System Power Center. Connect 
the wires to the SOLAR screw terminals according to the wiring diagram on page 64. Plug the solar valve 
actuator cable into three-pin socket marked VLV A on the EasyTouch PL4/PSL4 Control System main circuit 
board. If a solar booster pump is being installed, connect the pump to a power relay and plug a low voltage 
cable from relay into the two-pin socket marked SOLAR on the EasyTouch PL4/PSL4 Control System main 
circuit board. 

To access the Solar menu:

MENU

s

SETTING

w

SOLAR

w

SOLAR

Up/Down buttons: 

Select a circuit that will switch the filter pump to high speed. You can set up to four circuits to 

use a two-speed pump (

1

/4, 

2

/4, 

3

/4, 

4

/4). 

 

Right button: 

Move to assign a circuit setting.

 

Up/Down buttons:

 Select the circuit to assign to a two-speed pump. The generic circuits names are: 

NONE, SPA, 

POOL, AUX 1-3, FEATURE 1-2, SOLAR, HEATER, POOL HEATER, SPA HEATER and FREEZE.

 Selecting 

NONE does not assign a circuit.

 Note: You can use a Feature circuit to change a 2-Speed pump to high speed.  

Right button: 

Assign the next circuit (

2

/4). 

 

Up/Down buttons: 

Select the first digit for the circuit number (

1

/4, 

2

/4, 

3

/4, 

4

/4).

 

Right button: 

Move to circuit setting.

 

Up/Down buttons: 

Select the next circuit. When finished press the 

Menu

 button. 

 

Solar: 

Press the 

Up/Down button

 to select which solar screen to 

view. Press the 

Right 

Press the 

Up/Down button

 to select which solar screen to view. Press the 

Right button

 to select the setting and the 

Up/Down button

 to change a 

setting or value

.  

Screen (1/3): ENABLE SOLAR:

 Is the pool using solar heat? Select 

Yes

 or 

No

 to enable solar heat. To display the solar selection as a heat source in the 

main screen, select 

Yes

.

2-Speed Pmp  1/4 

 

Circuit: 

[SPA HEATER     ] 

       

Solar             1/3 

 

Enable:        Yes 

Heat Pump:  No 

       

Solar             2/3 

Enable Freeze 

Enable:        Yes/ No   

       

Solar             3/3 

Temperature Diff 

Start:    6°  

Run :    4°  

       

Summary of Contents for EASYTOUCH PL4

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands